- 您現在的位置：買賣IC網 > Datasheet目錄3 > 67-22/R6G6C-B09/2T (Everlight Electronics Co Ltd)LED MULTI COLOR PLCC Datasheet資料下載
參數資料
| 型號： | 67-22/R6G6C-B09/2T |
| 廠商： | Everlight Electronics Co Ltd |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 350K |
| 描述： | LED MULTI COLOR PLCC |
| 標準包裝： | 2,000 |
| 顏色： | 綠，紅 |
| Millicandela 等級： | 63mcd 綠，99mcd 紅 |
| 正向電壓： | 2.05V |
| 電流 - 測試： | 20mA |
| 波長 - 主： | 572nm，624nm |
| 波長 - 峰值： | 575nm，632nm |
| 視角： | 130° |
| 透鏡類型： | 透明 |
| 透鏡樣式/尺寸： | 矩形，帶平頂，2.64mm x 2.14mm |
| 封裝/外殼： | 4-PLCC |
| 尺寸/尺寸： | 3.50mm L x 2.80mm W |
| 高度： | 1.90mm |
| 安裝類型： | 表面貼裝 |
| 包裝： | 帶卷 (TR) |
DATASHEET
SMD REFLECTOR
67-22/R6G6C-B09/2T
10
Copyright ?2010, Everlight All Rights Reserved. Release Date : 2013.04.26. Issue No: DSE-0000926
www.everlight.com
Pre-heating
150~200癈
60~120sec.
3癈/sec.Max.
Above 217癈
60~150sec.
260癈 Max.
10sec. Max.
6癈/sec.Max.
Above255癈
30sec.Max.
recautions for Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less.
2.3 After opening the package: The LED's floor life are 168 hours under 30 or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60? for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
4. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in
less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each
terminal. Be careful because the damage of the product is often started at the time of the hand solder.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head
soldering iron should be used (as below figure). It should be confirmed beforehand whether the
相關PDF資料 |
PDF描述 |
|---|---|
| 67-31B/GHC-YX2Y2MZ3/2T | LED TOPLED 3PLCC SMD |
| 7010X13 | LED YELLOW NON-DIFF 1206 SMD |
| 7011X1/17 | LED RED NON-DIFF 1206 SMD |
| 7016X3 | LED 585NM YLW NON-DIFF 1208 SMD |
| 7016X5/7 | LED GREEN/YELLOW CLEAR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 67-22-R6Y2C-B31-2T | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:Top View LEDs |
| 6722-RC | 功能描述:固定電感器 900uH 15% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| 67-22SDRSYGC/S530-A2/TR8 | 制造商:Everlight Electronics CO., LTD 功能描述:67-22SDRSYGC/S530-A2/TR8 |
| 67-22SDRSYGC/S530-A2/TR8---- | 制造商:Everlight Electronics CO., LTD 功能描述:67-22SDRSYGC/S530-A2/TR8 |
| 67-22SDRVGC | 制造商:A-BRIGHT 制造商全稱:A-BRIGHT Inc 功能描述:Top View LEDs With Bi-Color |
發布緊急采購，3分鐘左右您將得到回復。