- 您現在的位置：買賣IC網 > PDF目錄375846 > FM24C32U (Fairchild Semiconductor Corporation) 32K-Bit Standard 2-Wire Bus Interface Serial EEPROM PDF資料下載
參數資料
| 型號： | FM24C32U |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 32K-Bit Standard 2-Wire Bus Interface Serial EEPROM |
| 中文描述： | 32K的位標準2線總線接口的串行EEPROM |
| 文件頁數： | 10/13頁 |
| 文件大小： | 85K |
| 代理商： | FM24C32U |
10
www.fairchildsemi.com
FM24C32U Rev. A.1
F
Write Operations
BYTE WRITE
For byte write operation, two bytes of address are required after
the slave address. These two bytes select 1 out of the 4096
locations in the memory. The master provides these two address
bytes and for each address byte received, FM24C32U responds
with an acknowledge pulse. Master then provides a byte of data
to be written into the memory. Upon receipt of this data, FM24C32U
responds with an acknowledge pulse. The master then terminates
the transfer by generating a stop condition, at which time the
FM24C32U begins the internal write cycle to the memory. While
the internal write cycle is in progress the FM24C32U inputs are
disabled, and the device will not respond to any requests from the
master for the duration of t
WR
. Refer Figure 4 for the address,
acknowledge and data transfer sequence.
PAGE WRITE
To minimize write cycle time, FM24C32U offers Page Write
feature, which allows simultaneous programming of up to 32
contiguous bytes. To facilitate this feature, the memory array is
organized in terms of
“
Pages
”
. A Page consists of 32 contiguous
byte locations starting at every 32-Byte address boundary (for
example, starting at array address 0x0000, 0x0020, 0x0040 etc.).
Page Write operation is confined to a single page. In other words
a Page Write operation will not cross over to locations on the next
page but will
“
roll over
”
to the beginning of the same page
whenever end of page is reached and additional data bytes are a
continued to be provided. A Page Write operation can be initiated
to begin at any location within a page (starting address of the Page
Write operation need not be the starting address of a Page).
S
T
O
P
A
C
K
A
C
K
Bus Activity:
Master
SDA Line
Bus Activity:
EEPROM
A
C
K
A
C
K
DATA n
DATA n+31
A
C
K
WORD
ADDRESS (1)
WORD
ADDRESS (0)
SLAVE
ADDRESS
S
T
A
R
T
S
T
O
P
A
C
K
Bus Activity:
Master
SDA Line
Bus Activity:
EEPROM
A
C
K
DATA
A
C
K
A
C
K
WORD
ADDRESS (1)
WORD
ADDRESS (0)
SLAVE
ADDRESS
S
T
A
R
T
Page Write is initiated in the same manner as the Byte Write
operation; but instead of terminating the cycle after transmitting
the first data byte, the master can further transmit up to 31 more
bytes. After the receipt of each byte, FM24C32U will respond with
an acknowledge pulse, increment the internal address counter to
the next address, and is ready to accept the next data. If the master
should transmit more than 32 bytes prior to generating the STOP
condition, the address counter will
“
roll over
”
and previously
loaded data will be re-loaded. As with the Byte Write operation, all
inputs are disabled until completion of the internal write cycle.
Refer Figure 5for the address, acknowledge, and data transfer
sequence.
Acknowledge Polling
Once the stop condition is issued to indicate the end of the host
’
s
write operation, the FM24C32U initiates the internal write cycle.
ACK polling can be initiated immediately. This involves issuing the
start condition followed by the slave address for a write operation.
If the FM24C32U is still busy with the write operation, no ACK will
be returned. If the FM24C32U has completed the write operation,
an ACK will be returned and the host can then proceed with the
next read or write operation.
Write Protection
Programming of the upper half (upper 8Kbit) of the memory will not
take place if the WP pin of the FM24C32U is connected to V
CC
.
The FM24C32U will respond to slave and byte addresses; but if
the memory accessed is write protected by the WP pin, the
FM24C32U will not generate an acknowledge after the first byte
of data has been received. Thus the program cycle will not be
started when the stop condition is asserted.
Byte Write (Figure 4)
Page Write (Figure 5)
相關PDF資料 |
PDF描述 |
|---|---|
| FM24C32UFTEM8 | EEPROM |
| FM24C32UFTEN | EEPROM |
| FM24C32UFTHEM8 | EEPROM |
| FM24C32UFTHEN | EEPROM |
| FM24C32UFTHM8 | EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM24C32UEM8 | 功能描述:電可擦除可編程只讀存儲器 USE 511-M24C32-MN6 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C32UEM8X | 功能描述:電可擦除可編程只讀存儲器 DISC BY MFG 7/03 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C32UEN | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FM24C32UFEM8 | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C32UFEM8X | 功能描述:電可擦除可編程只讀存儲器 DISC BY MFG 7/03 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。