- 您現在的位置：買賣IC網 > PDF目錄375847 > FM25C020U (Fairchild Semiconductor Corporation) 14=2X7 0.1" T/H MALE HDR SN PDF資料下載
參數資料
| 型號： | FM25C020U |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 14=2X7 0.1" T/H MALE HDR SN |
| 中文描述： | 的2K位SPI⑩的CMOS EEPROM的串行接口 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 105K |
| 代理商： | FM25C020U |
8
www.fairchildsemi.com
FM25C020U Rev. B
F
The RDSR command requires the following sequence. The /CS
pin is pulled low to select the EEPROM and then the RDSR
opcode is transmitted on the SI pin. After this is done, data on the
SI pin becomes don
’
t care. The data from the Status Register is
then shifted out on the SO pin starting with D7 bit first and D0 last.
See Figure 6.
FIGURE 6. Read Status Register
TABLE 4. Block Write Protection Levels
Level
Status Register Bits
Array
Address
Protected
None
BP1
0
BP0
0
0
1
0
1
C0-FF
2
1
0
80-FF
3
1
1
00-FF
A WRITE command requires the following sequence. The /CS pin
is pulled low to select the EEPROM, then the WRITE opcode is
transmitted on the SI pin followed by the byte address (A7-A0) and
followed by the data (D7-D0) to be written. See Figure 9.
FIGURE 9. Byte Write
/CS
SI
SO
RDSR
OP-CODE
RDSR DATA
WRITE ENABLE (WREN):
When V
is applied to the EEPROM, it
“
powers up
”
in a write-
disabled state. Therefore, all programming modes (Write to memory
array and Status register), must be preceded by a WRITE EN-
ABLE (WREN) instruction. See Figure7.
FIGURE 7. Write Enable
/CS
SI
SO
WREN Op-Code
WRITE DISABLE (WRDI):
Executing this instruction disables all programming modes (Write
to memory array and Status register), preventing the EEPROM
from accidental writes. Once WRDI instruction is executed,
WREN instruction should be executed to re-enable all program-
ming modes. See Figure8.
FIGURE 8. Write Disable
/CS
SI
SO
WRDI Op-Code
WRITE SEQUENCE (WRITE):
Write to the array is enabled only when /WP pin is held high and
the EEPROM is write enabled previously (via WREN instruction).
Also, the address of the memory location(s) to be programmed
must be outside the protected address field selected by the Block
Write Protection Level. See Table 4.
/CS
SI
SO
Write
Op-Code
Byte
Addr
Data
High Z
Internally, the programming will start after the /CS pin is brought
back to a high level. Note that the LOW to HIGH transition of the
/CS pin must occur during the SCK low time immediately after
clocking in the D0 data bit. See Figure10.
FIGURE 10. Start of Programming
SCK
SI
SO
/CS
D0
D1
D2
High Z
Start of internal
Programming status (Busy/Ready) of the EEPROM can be deter-
mined by executing a READ STATUS REGISTER (RDSR) in-
struction after a write command. Upon executing the RDSR
instruction, if Bit 0 of the RDSR data is
“
1
”
, it indicates the WRITE
cycle is still in progress. If it is
“
0
”
then the WRITE cycle has ended.
Note that while the internal programming is still in progress (Bit 0
= 1), only the RDSR instruction is enabled. It is recommended that
no other instruction be issued till the internal programming is
complete.
相關PDF資料 |
PDF描述 |
|---|---|
| FM25C020UE | LOW PROFILE .025 SQ STRIPS |
| FM25C020UV | CONN-HDR,7P 1ROW,.1SP, TIN, LO PF |
| FM25C040 | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| FM25C040U | LOW PROFILE .025 SQ STRIPS |
| FM25C040UE | CONN,HEADER,2X8,AV,.100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM25C020UE | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:2K-Bit SPI⑩ Interface Serial CMOS EEPROM |
| FM25C020UEM8 | 功能描述:電可擦除可編程只讀存儲器 SOIC-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM25C020UEM8X | 功能描述:電可擦除可編程只讀存儲器 DISC BY MFG 7/03 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM25C020UEMT8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
| FM25C020UEN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPI Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。