- 您現在的位置：買賣IC網 > Datasheet目錄13 > GM5BW97331A (Sharp Microelectronics)LED WHITE 5000K 20MA 3.2V PLCC4 Datasheet資料下載
參數資料
| 型號： | GM5BW97331A |
| 廠商： | Sharp Microelectronics |
| 文件頁數： | 14/18頁 |
| 文件大小： | 1051K |
| 描述： | LED WHITE 5000K 20MA 3.2V PLCC4 |
| 產品目錄繪圖： | LED PLCC-2 Side LED PLCC-2 Top 3-LED Schematic |
| 標準包裝： | 1 |
| 顏色： | 冷白色 |
| Millicandela 等級： | 7000mcd |
| 正向電壓： | 3.2V |
| 電流 - 測試： | 20mA |
| 波長 - 主： | 5000K |
| 視角： | 120° |
| 透鏡樣式/尺寸： | 圓形，帶平頂，2.4mm |
| 封裝/外殼： | 4-PLCC |
| 尺寸/尺寸： | 3.20mm L x 2.80mm W |
| 高度： | 1.90mm |
| 安裝類型： | 表面貼裝 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 2920 (CN2011-ZH PDF) |
| 其它名稱： | 425-2741-6 |
14
Preliminary
GM5BW97331A
?SPAN class="pst GM5BW97331A_2663707_3">Design Notes
1. Do not allow the circuit to apply any reverse voltage to the LEDs at any time, operating or not. Do not bias this
part in any manner when it is not operating. Reverse voltage can also be induced via EMF, generated by ambi-
ent light falling on this part. When these parts are operated in series, connect a zener diode parallel to each part
to protect them from reverse voltage.
2. This part can be damaged by mechanical stress. Be certain that assembly steps do not stress this part; pay
particular attention to pick-and-place equipment. Verify placing pressure and do not allow the collet to contact
the resin of this part.
3. This product uses blue LED chips in combination with yellow phosphor to achieve its color. There may be some
slight color change due to afterglow of the phosphor when driving this part with pulsed power.
4. This part has a high light output. Looking directly at it during full power output may cause injury.
5. Sharp recommends taking proper personal and environmental static control precautions when handling this part.
6. This device incorporates thermally conductive materials to allow heat to be transferred from it to the circuit
board. For best reliability, do not locate other sources of heat near the LED, and design the circuit board for
effective heat dissipation. Keep the parts case temperature under 100癈 (LED ON) including self-heating.
7. Handle these parts in a clean environment; dust may be difficult to remove and can affect optical performance.
8. Confirm the parts performance, reliability, and resistance to degradation, if exposing it to these environments:
"Direct sunlight, outdoor exposure, dusty conditions
"In water, oil, medical fluids, and organic solvents
"Excessive moisture, such as dew or condensation
"Corrosive (salt) air or corrosive gases, such as Cl, H
2
S, NH
3
, SO
2
, NO
X
?SPAN class="pst GM5BW97331A_2663707_3">Manufacturing Guidelines
?SPAN class="pst GM5BW97331A_2663707_3">Storage and Handling
1. Moisture-proofing: These parts are shipped in vacuum-sealed bags to keep them dry and ready for use.
See Fig. 18.
2. Store these parts between 5癈 and 30癈, at a relative humidity of less than 70%; for no more than one year
from the production date.
3. After breaking the package seal, maintain the environment within 5癈 to 30癈, at a relative humidity of less than
60%. Solder the parts within 3 days.
4. If the parts will not be used immediately, repack them in a dry box, or re-vacuum-seal them with a desiccant.
5. If the parts are exposed to air for more than 3 days, or if the silica gel telltale indicates moisture contamination,
bake the parts:
"When in the tape carrier, bake them at a temperature of 95癈 to 100癈, for 16 to 24 hours.
"When loose or on a PCB, bake them at a temperature of 110癈 to 120癈, for 8 to 12 hours.
"Note that the reels may become distorted if they are in a stack when baking. Confirm that the parts have cooled
to room temperature after baking.
?SPAN class="pst GM5BW97331A_2663707_3">Cleaning Instructions
1. Sharp does not recommend cleaning printed circuit boards containing this device, or cleaning this device with
ultrasonic methods. Process chemicals will affect the structural and optical characteristics of this device.
2. Sharp recommends the use of a solder paste that does not require cleaning.
3. Do not clean this part ultrasonically.
相關PDF資料 |
PDF描述 |
|---|---|
| GM5BW97333A | LED WHITE 11500K 20MA 3.2V PLCC4 |
| GM5GC96270A | LED GREEN 30MA 3.3V SMD |
| GM5JV95200AE | LED AMBER CLEAR 3228 SMD |
| GM5WA94310A | LED RED/GRN/BLU 30MA 5V SMD |
| GM5ZR96270A | LED RED 30MA 5V SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GM5BW97332A | 功能描述:標準LED-SMD White 6500K 20mA 3.5V RoHS:否 制造商:Vishay Semiconductors 封裝 / 箱體:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明顏色:Red 波長/色溫:631 nm 透鏡顏色/類型:Water Clear 正向電流:30 mA 正向電壓:2 V 光強度:54 mcd 顯示角:130 deg 系列:VLMx1500 封裝:Reel |
| GM5BW97333A | 功能描述:標準LED-SMD White 11000K 20mA 3.5V RoHS:否 制造商:Vishay Semiconductors 封裝 / 箱體:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明顏色:Red 波長/色溫:631 nm 透鏡顏色/類型:Water Clear 正向電流:30 mA 正向電壓:2 V 光強度:54 mcd 顯示角:130 deg 系列:VLMx1500 封裝:Reel |
| GM5BW9773A | 功能描述:標準LED-SMD White 5300K RoHS:否 制造商:Vishay Semiconductors 封裝 / 箱體:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明顏色:Red 波長/色溫:631 nm 透鏡顏色/類型:Water Clear 正向電流:30 mA 正向電壓:2 V 光強度:54 mcd 顯示角:130 deg 系列:VLMx1500 封裝:Reel |
| GM5EG95200A | 功能描述:標準LED-SMD 2.8 x 3.5 x 1.9 Chip LED Yelow-Green RoHS:否 制造商:Vishay Semiconductors 封裝 / 箱體:0402 LED 大小:1 mm x 0.5 mm x 0.35 mm 照明顏色:Red 波長/色溫:631 nm 透鏡顏色/類型:Water Clear 正向電流:30 mA 正向電壓:2 V 光強度:54 mcd 顯示角:130 deg 系列:VLMx1500 封裝:Reel |
| GM5GC01200AC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HIGH-LUMINOSITY LED LAMP |
發布緊急采購，3分鐘左右您將得到回復。