- 您現在的位置：買賣IC網 > PDF目錄382287 > MAX810LTR (ON SEMICONDUCTOR) 3-Pin Microprocessor Reset Monitors PDF資料下載
參數資料
| 型號： | MAX810LTR |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | 3-Pin Microprocessor Reset Monitors |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | TO-236, SOT-23, 3 PIN |
| 文件頁數： | 4/8頁 |
| 文件大小： | 119K |
| 代理商： | MAX810LTR |
MAX809, MAX810
http://onsemi.com
4
APPLICATIONS INFORMATION
VCC Transient Rejection
The MAX809/810 provides accurate V
CC
monitoring and
reset timing during power–up, power–down, and
brownout/sag conditions, and rejects negative–going
transients (glitches) on the power supply line. Figure 1
shows the maximum transient duration vs. maximum
negative excursion (overdrive) for glitch rejection. Any
combination of duration and overdrive which lies
under
the
curve will
not
generate a reset signal. Combinations above
the curve are detected as a brownout or power–down.
Transient immunity can be improved by adding a capacitor
in close proximity to the V
CC
pin of the MAX809/810.
Figure 1. Maximum Transient Duration vs. Overdrive
for Glitch Rejection at 25
°
C
Duration
VTH
Overdrive
VCC
TA = +25
°
C
MAX8xxL/M/J
1
10
100
1000
0
90
160
240
320
400
M
RESET COMPARATOR OVERDRIVE,
(VTH – VCC (mV)
MAX8xxR/S/T
RESET Signal Integrity During Power–Down
The MAX809 RESET output is valid to V
CC
= 1.0V.
Below this voltage the output becomes an ”open circuit” and
does not sink current. This means CMOS logic inputs to the
μ
P will be floating at an undetermined voltage. Most digital
systems are completely shutdown well above this voltage.
However, in situations where RESET must be maintained
valid to V
CC
= 0V, a pull–down resistor must be connected
from RESET to ground to discharge stray capacitances and
hold the output low (Figure 2). This resistor value, though
not critical, should be chosen such that it does not
appreciably load RESET under normal operation (100k
will be suitable for most applications). Similarly, a pull–up
resistor to V
CC
is required for the MAX810 to ensure a valid
high RESET for V
CC
below 1.0V.
VCC
VCC
RESET
R1
100 k
MAX809
GND
Figure 2. Ensuring RESET Valid to VCC = 0 V
Processors With Bidirectional I/O Pins
Some
μ
P’s (such as Motorola 68HC11) have
bi–directional reset pins. Depending on the current drive
capability of the processor pin, an indeterminate logic level
may result if there is a logic conflict. This can be avoided
by adding a 4.7k resistor in series with the output of the
MAX809/810 (Figure 3). If there are other components in
the system which require a reset signal, they should be
buffered so as not to load the reset line. If the other
components are required to follow the reset I/O of the
μ
P, the
buffer should be connected as shown with the solid line.
VCC
MAX809
VCC
P
RESET
GND
GND
47 k
Figure 3. Interfacing to Bidirectional Reset I/O
RESET
VCC
BUFFERED RESET
TO OTHER SYSTEM
COMPONENTS
BUFFER
相關PDF資料 |
PDF描述 |
|---|---|
| MAX810MTR | 3-Pin Microprocessor Reset Monitors |
| MAX810RTR | 3-Pin Microprocessor Reset Monitors |
| MAX810STR | 3-Pin Microprocessor Reset Monitors |
| MAX810TTR | 3-Pin Microprocessor Reset Monitors |
| MAX809xTR | 3-Pin Microprocessor Reset Monitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX810LTRG | 功能描述:監控電路 4.63V uP Reset RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX810LTRG | 制造商:ON Semiconductor 功能描述:Microprocessor Support IC |
| MAX810LW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-pin microprocessor resets |
| MAX810M | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3-Pin Microprocessor Reset Circuits |
| MAX810MCPA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Voltage Detector |
發布緊急采購，3分鐘左右您將得到回復。