- 您現在的位置：買賣IC網 > PDF目錄371076 > MC908QL4DT (Motorola, Inc.) Microcontrollers PDF資料下載
參數資料
| 型號： | MC908QL4DT |
| 廠商： | Motorola, Inc. |
| 英文描述： | Microcontrollers |
| 中文描述： | 微控制器 |
| 文件頁數： | 162/222頁 |
| 文件大?。?/td> | 2861K |
| 代理商： | MC908QL4DT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁當前第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁
Slave LIN Interface Controller (SLIC) Module
MC68HC908QL4 MC68HC908QL3 MC68HC908QL2 Data Sheet, Rev. 4
162
Freescale Semiconductor
will resume. If the SLIC was in SLIC stop mode, SLCSV will indicate wakeup as the interrupt source so
that the user knows that the SLIC module brought the MCU out of stop or wait.
In a LIN system, a system message is generally sent to all nodes to indicate that they are to enter
low-power network sleep mode. After a node enters sleep mode, it waits for outside events, such as
switch or sensor inputs or network traffic to bring it out of network sleep mode. If the node using the SLIC
module is awakened by a source other than network traffic, such as a switch input, the LIN specification
requires this node to issue a wake-up signal to the rest of the network. The SLIC module supports this
feature using WAKETX in SLCC2. The user software may set this bit and one LIN wake-up signal is
immediately transmitted on the bus, then the bit is automatically cleared by the SLIC module. If another
wake-up signal is required to be sent, the user must set WAKETX again.
In a LIN system, the LIN physical interface can often also provide an output to the IRQ pin to provide a
wake-up mechanism on network activity. The physical layer might also control voltage regulation supply
to the MCU, cutting power to the MCU when the physical layer is placed in its low-power mode. The user
must take care to ensure that the interaction between the physical layer, IRQ pin, SLIC transmit and
receive pins, and power supply regulator is fully understood and designed to ensure proper operation.
14.9.12 Polling Operation
It is possible to operate the SLIC module in polling mode, if desired. The primary difference is that the
SLIC interrupt request should not be enabled (SLCIE = 0). The SLCSV will update and operate properly
and interrupt requests will be indicated with the SLCF flag, which can be polled to determine status
changes in the SLIC module. It is required that the polling rate be fast enough to ensure that SLIC status
changes be recognized and processed in time to ensure that all application timings can be met.
14.9.13 LIN Data Integrity Checking Methods
The SLIC module supports two different LIN-based data integrity options:
The first option supports LIN 1.3 and older methods of checksum calculations.
The second option supports an optional additional enhanced checksum calculation which has
greater data integrity coverage.
The LIN 1.3 and earlier specifications transmit a checksum byte in the “CHECKSUM FIELD” of the LIN
message frame. This CHECKSUM FIELD contains the inverted modulo-256 sum over all data bytes. The
sum is calculated by an “ADD with Carry” where the carry bit of each addition is added to the least
significant bit (LSB) of its resulting sum. This guarantees security also for the MSBs of the data bytes. The
sum of modulo-256 sum over all data bytes and the checksum byte must be ’0xFF’.
An optional checksum calculation can also be performed on a LIN data frame which is very similar to the
LIN 1.3 calculation, but with one important distinction. This enhanced calculation simply includes the
identifier field as the first value in the calculation, whereas the LIN 1.3 calculation begins with the least
significant byte of the data field (which is the first byte to be transmitted on the bus). This enhanced
calculation further ensures that the identifier field is correct and ties the identifier and data together under
a common calculation, ensuring greater reliability.
In the SLIC module, either checksum calculation can be performed on any given message frame by
simply writing or clearing CHKMOD in SLCDLC, as desired, when the identifier for the message frame is
decoded. The appropriate calculation for each message frame should be decided at system design time
and documented in the LIN description file, indicating to the user which calculation to use for a particular
identifier.
相關PDF資料 |
PDF描述 |
|---|---|
| MC908QL4DW | Microcontrollers |
| MC908QL4M | Microcontrollers |
| MC908QL4V | Microcontrollers |
| MC912DG128x | microcontroller unit 16BIT DEVICE |
| MC68HC912DG128A | microcontroller unit 16BIT DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC908QL4DW | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC908QL4M | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Microcontrollers |
| MC908QL4MDT | 功能描述:IC MCU 8BIT 4K FLASH 16-TSSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:HC08 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
| MC908QL4MDTE | 功能描述:8位微控制器 -MCU NITRON LINE EPP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MC908QL4MDTE | 制造商:Freescale Semiconductor 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。