- 您現在的位置：買賣IC網 > PDF目錄376245 > OP484 (Analog Devices, Inc.) Precision Rail-to-Rail Input & Output Operational Amplifiers(精密滿幅度輸入輸出運放) PDF資料下載
參數資料
| 型號： | OP484 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Precision Rail-to-Rail Input & Output Operational Amplifiers(精密滿幅度輸入輸出運放) |
| 中文描述： | 精密軌到軌輸入 |
| 文件頁數： | 16/20頁 |
| 文件大小： | 370K |
| 代理商： | OP484 |
REV. 0
–16–
OP184/OP284/OP484
Obviously, it is desirable to keep this comparison voltage small,
since it becomes a significant portion of the overall dropout
voltage. Here, the 20 mV reference, is higher than the typical
offset of the OP284, but still reasonably low as a percentage of
V
OUT
(< 0.5%). In adapting the limiter for other I
LIMIT
levels,
sense resistor R
S
should be adjusted along with R7-R8, to main-
tain this threshold voltage between 20 mV and 50 mV.
Performance of the circuit is excellent. For the 4.5 V output
version, the measured dc output change for a 225 mA load
change was on the order of a few microvolts, while the dropout
voltage at this same current level was about 30 mV. T he current
limit as shown is 400 mA, which allows the circuit to be used at
levels up to 300 mA or more. While the Q1 device can actually
support currents of several amperes, a practical current rating
takes into account the SO-8 device’s 2.5 W, 25
°
C dissipation.
A short circuit current of 400 mA at an input level of 5 V will
cause a 2 W dissipation in Q1, so other input conditions should
be considered carefully in terms of Q1’s potential overheating.
Of course, if higher powered devices are used for Q1, this circuit
can support outputs of tens of amperes as well as the higher
V
OUT
levels noted above.
T he circuit shown can be used either as a standard low dropout
regulator, or it can also be used with ON/OFF control. By
driving Pin 3 of U1 with the optional logic control signal V
C
, the
output is switched between ON and OFF. Note that when the
output is OFF in this circuit, it is still active (i.e., not an open cir-
cuit). T his is because the OFF state simply reduces the voltage
input to R1, leaving the U1A/B amplifiers and Q1 still active.
When ON/OFF control is used, resistor R10 should be used
with U1, to speed ON-OFF switching, and to allow the output
of the circuit to settle to a nominal zero voltage. Components
D3 and R11 also aid in speeding up the ON-OFF transition, by
providing a dynamic discharge path for C2. OFF-ON transition
time is less than 1 ms, while the ON-OFF transition is longer,
but under 10 ms.
A +3 V, 50 Hz/60 Hz Active Notch Filter with False Ground
T o process signals in a single-supply system, it is often best
to use a false ground biasing scheme. A circuit that uses this
approach is illustrated in Figure 56. In this circuit, a false-ground
circuit biases an active notch filter used to reject 50 Hz/60 Hz
power line interference in portable patient monitoring equip-
ment. Notch filters are quite commonly used to reject power
line frequency interference which often obscures low frequency
physiological signals, such as heart rates, blood pressure read-
ings, EEGs, EK Gs, et cetera. T his notch filter effectively
squelches 60 Hz pickup at a filter Q of 0.75. Substituting
3.16 k
resistors for the 2.67 k
in the twin-T section
(R1 through R5) configures the active filter to reject 50 Hz
interference.
1
3
5
6
7
11
2
+3V
R1
2.67k
C1
1μF
C2
1μF
R3
2.67k
C3
2μF
(1μF x 2)
R4
2.67k
R5
1.33k
(2.67k
÷
2)
R2
2.67k
V
O
R6
10k
V
IN
R8
1k
A2
A1
8
A3
R7
1k
R11
10k
4
10
9
C5
0.03μF
R12
150
R10
20k
C4
1μF
R9
20k
+3V
1.5V
C6
1μF
A1, A2, A3 = OP484
Q = 0.75
NOTE: FOR 50Hz APPLICATIONS
CHANGE R1–R4 TO 3.1k
AND R5 TO 1.58k
(3.16k
÷
2).
Figure 56. A +3 V Single Supply, 50/60 Hz Active Notch
Filter with False Ground
Amplifier A3 is the heart of the false-ground bias circuit. It
simply buffers the voltage developed at R9 and R10 and is the
reference for the active notch filter. Since the OP484 exhibits a
rail-to-rail input common-mode range, R9 and R10 are chosen
to split the +3 V supply symmetrically. An in-the-loop compen-
sation scheme is used around the OP484 that allows the op amp
to drive C6, a 1
μ
F capacitor, without oscillation. C6 maintains
a low impedance ac ground over the operating frequency range
of the filter.
T he filter section uses a OP484 in a twin-T configuration whose
frequency selectivity is very sensitive to the relative matching of
the capacitors and resistors in the twin-T section. Mylar is the
material of choice for the capacitors, and the relative matching
of the capacitors and resistors determines the filter’s pass band
symmetry. Using 1% resistors and 5% capacitors produces
satisfactory results.
相關PDF資料 |
PDF描述 |
|---|---|
| OP490FY | Low Voltage Micropower Quad Operational Amplifier |
| OP490AY | Low Voltage Micropower Quad Operational Amplifier |
| OP490EY | Low Voltage Micropower Quad Operational Amplifier |
| OP490GP | Low Voltage Micropower Quad Operational Amplifier |
| OP490GS | Low Voltage Micropower Quad Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP4840002C | 制造商:Analog Devices 功能描述: |
| OP4840016SZR7 | 制造商:Analog Devices 功能描述: |
| OP484AM-EMX | 制造商:Analog Devices 功能描述:OP484AM-EMX - Bulk |
| OP484AY/QMLR | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。