- 您現在的位置：買賣IC網 > PDF目錄373909 > AD7575JN (ANALOG DEVICES INC) LC2MOS 5 us 8-Bit ADC with Track/Hold PDF資料下載
參數資料
| 型號： | AD7575JN |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | LC2MOS 5 us 8-Bit ADC with Track/Hold |
| 中文描述： | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDIP18 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-18 |
| 文件頁數： | 5/12頁 |
| 文件大小： | 146K |
| 代理商： | AD7575JN |
AD7575
–5–
REV. B
TIMING AND CONTROL OF THE AD7575
The two logic inputs on the AD7575,
CS
and
RD
, control both
the starting of conversion and the reading of data from the part.
A conversion is initiated by bringing both of these control inputs
LOW. Two interface options then exist for reading the output
data from the AD7575. These are the Slow Memory Interface
and ROM Interface, their operation is outlined below. It should
be noted that the TP pin of the AD7575 must be hard-wired
HIGH to ensure correct operation of the part. This pin is used
in testing the device and should not be used as a feedthrough pin
in double-sided printed circuit boards.
SLOW MEMORY INTERFACE
The first interface option is intended for use with microproces-
sors that can be forced into a WAIT STATE for at least 5
μ
s.
The microprocessor (such as the 8085A) starts a conversion and
is halted until the result of the conversion is read from the con-
verter. Conversion is initiated by executing a memory READ to
the AD7575 address, bringing
CS
and
RD
LOW.
BUSY
subse-
quently goes LOW (forcing the microprocessor READY input
LOW), placing the processor into a WAIT state. The input
signal, which had been tracked by the analog input, is held on
the third falling clock edge of the input clock after
CS
and
RD
have gone LOW (see Figure 12). The AD7575 then performs a
conversion on this acquired input signal value. When the con-
version is complete (
BUSY
goes HIGH), the processor com-
pletes the memory READ and acquires the newly converted
data. The timing diagram for this interface is shown in Figure 3.
ADDRESS
DECODE
ADDRESS
LATCH
AD7575*
TP
CS
RD
BUSY
DB0–DB7
ADDRESS BUS
DATA BUS
+5V
A8–A15
S0
ALE
AD0–AD7
READY
8085A–2
*LINEAR CIRCUITRY OMITTED FOR CLARITY
SO = 0 FOR READ CYCLES
Figure 4. AD7575 to 8085A-2 Slow Memory Interface
The major advantage of this interface is that it allows the micro-
processor to start conversion, WAIT, and then READ data with
a single READ instruction. The fast conversion time of the
AD7575 ensures that the microprocessor is not placed in a
WAIT state for an excessive amount of time.
Faster versions of many processors, including the 8085A-2, test
the condition of the READY input very soon after the start of
an instruction cycle. Therefore,
BUSY
of the AD7575 must go
LOW very early in the cycle for the READY input to be effec-
tive in forcing the processor into a WAIT state. When using the
8085A-2, the processor S0 status signal provides the earliest
possible indication that a READ operation is about to occur.
Hence, S0 (which is LOW for a READ cycle) provides the
READ signal to the AD7575. The connection diagram for the
AD7575 to 8085A-2 Slow Memory interface is shown in
Figure 4.
ROM INTERFACE
The alternative interface option on the AD7575 avoids placing
the microprocessor into a WAIT state. In this interface, a con-
version is started with the first READ instruction, and the sec-
ond READ instruction accesses the data and starts a second
conversion. The timing diagram for this interface is shown in
Figure 5. It is possible to avoid starting another conversion on
the second READ (see below).
Conversion is initiated by executing a memory READ instruc-
tion to the AD7575 address, causing
CS
and
RD
to go LOW.
Data is also obtained from the AD7575 during this instruction.
This is old data and may be disregarded if not required.
BUSY
goes LOW, indicating that conversion is in progress, and re-
turns HIGH when conversion is complete. Once again, the
input signal is held on the third falling edge of the input clock
after
CS
and
RD
have gone LOW.
The
BUSY
line may be used to generate an interrupt to the
microprocessor or monitored to indicate that conversion is
complete. The processor then reads the newly-converted data.
Alternatively, the delay between the convert start (first READ
instruction) and the data READ (second READ instruction)
must be at least as great as the AD7575 conversion time. For
the AD7575 to operate correctly in the ROM interface mode,
CS
and
RD
should not go LOW before
BUSY
returns HIGH.
Normally, the second READ instruction starts another conver-
sion as well as accessing the output data. However, if
CS
and
RD
are brought LOW within one external clock period of
BUSY
going HIGH, a second conversion does not occur.
t
5
t
1
t
2
t
6
t
7
t
CONV
HIGH IMPEDANCE
BUS
NEW
DATA
OLD DATA
HIGH IMPEDANCE
BUS
CS
RD
BUSY
DATA
t
3
Figure 3. Slow Memory Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| AD7575JP | LC2MOS 5 us 8-Bit ADC with Track/Hold |
| AD7575JR | LC2MOS 5 us 8-Bit ADC with Track/Hold |
| AD7575KN | LC2MOS 5 us 8-Bit ADC with Track/Hold |
| AD7575KP | LC2MOS 5 us 8-Bit ADC with Track/Hold |
| AD7575SE | LC2MOS 5 us 8-Bit ADC with Track/Hold |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7575JNZ | 功能描述:IC ADC 8BIT LC2MOS W/HOLD 18DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7575JP | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PLCC 制造商:Rochester Electronics LLC 功能描述:CMOS CONVERTER IC - Bulk |
| AD7575JP-REEL | 制造商:Analog Devices 功能描述:ADC Single SAR 8-bit Parallel 20-Pin PLCC T/R |
| AD7575JPZ | 功能描述:IC ADC 8BIT TRACK&HOLD 20-PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| AD7575JPZ-REEL | 功能描述:IC ADC 8BIT LC2MOS W/HOLD 20PLCC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。