- 您現在的位置：買賣IC網 > PDF目錄375841 > FM24C04A-S (Electronic Theatre Controls, Inc.) 4Kb FRAM Serial 3V Memory PDF資料下載
參數資料
| 型號： | FM24C04A-S |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | DRAM |
| 英文描述： | 4Kb FRAM Serial 3V Memory |
| 中文描述： | 4Kb的鐵電串行3V的記憶 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 110K |
| 代理商： | FM24C04A-S |
FM24C04A
Rev. 2.0
July 2003
6 of 12
S
A
Slave Address
0
Word Address
A
Data Byte
A
P
By Master
By FM24C04A
Start
Address & Data
Stop
Acknowledge
Figure 5. Byte Write
S
A
Slave Address
0
Word Address
A
Data Byte
A
P
By Master
By FM24C04A
Start
Address & Data
Stop
Acknowledge
Data Byte
A
Figure 6. Multiple Byte Write
Read Operation
There are two basic types of read operations. They are
current address read and selective address read. For
current address reads, the FM24C04A uses the internal
address latch to supply the lower 8 address bits. In a
selective read, the user performs a procedure to set
these lower address bits to a specific value.
Current Address & Sequential Read
The FM24C04A uses an internal latch to supply the
lower 8 address bits for a read operation. A current
address read uses the existing value in the address
latch as a starting place for the read operation. This is
the address immediately following that of the last
operation.
To perform a current address read, the bus master
supplies a slave address with the LSB set to 1. This
indicates that a read operation is requested. The page
select bit in the slave address specifies the block of
memory that is used for the read operation. After the
acknowledge, the FM24C04A will begin shifting out
data from the current address. The current address is
the bit from the slave address combined with the 8 bits
that were in the internal address latch.
Beginning with the current address, the bus master can
read any number of bytes. Thus, a sequential read is
simply a current address read with multiple byte
transfers. After each byte the internal address counter
will be incremented. Each time the bus master
acknowledges a byte, this indicates that the
FM24C04A should read out the next sequential byte.
There are four ways to properly terminate a read
operation. Failing to properly terminate the read will
most likely create a bus contention as the FM24C04A
attempts to read out additional data onto the bus. The
four valid methods are as follows.
1.
The bus master issues a no-acknowledge in the
9
th
clock cycle and a stop in the 10
th
clock cycle.
This is illustrated in the diagrams below. This is
the preferred method.
2.
The bus master issues a no-acknowledge in the
9
th
clock cycle and a start in the 10
th
.
3.
The bus master issues a stop in the 9
th
clock
cycle. Bus contention may result.
4.
The bus master issues a start in the 9
th
clock
cycle. Bus contention may result.
If the internal address reaches 1FFh, it will wrap
around to 000h on the next read cycle. Figures 7 and
8 show the proper operation for current address and
sequential reads.
Selective (Random) Read
A simple technique allows a user to select a random
address location as the starting point for a read
operation. This involves using the first two bytes of
a write operation to set the internal address byte
followed by subsequent read operations.
To perform a selective read, the bus master sends
out the slave address with the LSB set to 0. This
specifies a write operation. According to the write
protocol, the bus master then sends the word address
byte that is loaded into the internal address latch.
After the FM24C04A acknowledges the word
address, the bus master issues a start condition. This
simultaneously aborts the write operation and allows
the read command to be issued with the slave
address LSB set to a 1. The operation is now a
current address read. See Figure 9.
相關PDF資料 |
PDF描述 |
|---|---|
| FM24C05ULZ | 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM |
| FM24C17U | 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM |
| FM24C04UEM8 | I2C Serial EEPROM |
| FM24C04UEMT8 | I2C Serial EEPROM |
| FM24C04UEN | I2C Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM24C04A-STR | 功能描述:F-RAM 4K (512x8) 5V RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM24C04B | 制造商:RAMTRON 制造商全稱:RAMTRON 功能描述:4Kb Serial 5V F-RAM Memory |
| FM24C04B_13 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:4Kb Serial 5V F-RAM Memory |
| FM24C04B-G | 功能描述:F-RAM 4Kb Serial I2C 5V FRAM RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM24C04B-GTR | 功能描述:F-RAM 4Kb Serial I2C 5V FRAM RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
發布緊急采購，3分鐘左右您將得到回復。