- 您現在的位置：買賣IC網 > PDF目錄369230 > 68HC05BD2 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | 68HC05BD2 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 41/85頁 |
| 文件大小： | 302K |
| 代理商： | 68HC05BD2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
SECTION 6: OPERATING MODES
MOTOROLA
Page 31
MC68HC05BD7 Rev. 2.0
GENERAL RELEASE SPECIFICATION
its usual way to make COP Watchdog Timer meaningful in monitor applications. Execution
of the STOP instruction will be the same as that of the NOP instruction. Hence, I bit in the
Condition Code Register will not be cleared.
6.5.2
Program control register is provided for EPROM programming the device.
Programming Control Register (PCR)
ELAT—EPROM Latch Control
0 - EPROM address and data bus configured for normal read.
1 - EPROM address and data bus configured for programming (writes to
EPROM cause address and data to be latched). EPROM is in programming
mode and can not be read. This bit is not writable to 1 when no VPP voltage
is applied to the VPP pin.
PGM—EPROM Program Command
0 - Programming power to EPROM array is switched off.
1 - Programming power to EPROM array is switched on.
6.6
Low Power Modes
The MC68HC05BD7 has ONLY ONE low-power operational mode. The WAIT instruction
provides the only mode that reduces the power required for the MCU by stopping CPU
internal clock. The WAIT instruction is not normally used if the COP Watchdog Timer is
enabled.
The STOP instruction is not implemented in its normal sense
. The STOP
instruction will be interpreted as the NOP instruction by the CPU if it is ever encountered.
The flow of the WAIT mode is shown in
Figure 6-2
.
6.6.1
STOP Instruction
Since the execution of a normal STOP instruction results in the stoppage of clocks to all
modules, including the COP Watchdog Timer, this instruction is hence not implemented in
6.6.2
WAIT Instruction
In the WAIT Mode the internal processor clock is halted, suspending all processor and
internal bus activity. Other Internal clocks remain active, permitting interrupts to be
generated from the Multi-Function Timer, or a reset to be generated from the COP
Watchdog Timer. The Timer may be used to generate a periodic exit from the WAIT Mode.
Execution of the WAIT instruction automatically clears the I-bit in the Condition Code
Register, so that any hardware interrupt can wake up the MCU. All other registers, memory,
and input/output lines remain in their previous states.
0
7
ELAT
0
0
0
0
0
0
0
6
5
4
3
2
1
0
PGM
W
R
PCR
$001D
reset
相關PDF資料 |
PDF描述 |
|---|---|
| 68HC05BD7 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705BD7 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 68HC05BD7 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:SPECIFICATION REV 2.0 (General Release) |
| 68HC05C0FN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C0P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。