- 您現在的位置：買賣IC網 > PDF目錄369230 > 68HC05BD7 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | 68HC05BD7 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 17/85頁 |
| 文件大小： | 302K |
| 代理商： | 68HC05BD7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
SECTION 1: GENERAL DESCRIPTION
MOTOROLA
Page 7
MC68HC05BD7 Rev. 2.0
GENERAL RELEASE SPECIFICATION
1.2
Signal Description
1.2.1
VDD is the positive supply pin and VSS is the ground pin.
VDD and VSS
1.2.2
IRQ/VPP
This pin has two functions. While in user mode, this pin serves as IRQ, a general purpose
interrupt input which is software programmable for two choices of interrupt triggering
sensitivity. These options are: 1) negative edge-sensitive triggering only, or 2) both
negative edge-sensitive and level-sensitive triggering. In the latter case, either type of input
to the IRQ pin will produce the interrupt. This interrupt can be inhibited by setting the
INHIRQ bit in the MFT register. While in bootstrap mode, this pin is used as VPP pin for
HC705 version. It is used to supply high voltage needed for programming the user EPROM.
1.2.3
EXTAL, XTAL
The EXTAL and XTAL pins are the connections for the on-chip oscillator. The EXTAL, and
XTAL pins can accept the following sets of components:
1. A crystal as shown in
Figure 1-4(a)
2. An external clock signal as shown in
Figure 1-4(b)
The frequency, f
the internal operating frequency, f
OSC
, of the oscillator or external clock source is divided by two to produce
.
OP
1.2.3.1
Crystal Oscillator
The circuit in shows
crystal. The crystal manufacturer’s recommendations should be followed, as the crystal
parameters determine the external component values required to provide maximum
stability and reliable start-up. The load capacitance values used in the oscillator circuit
design should include all stray capacitances. The crystal and components should be
mounted as close as possible to the pins for start-up stabilization and to minimize output
distortion. An
internal start-up resistor
of approximately
EXTAL and XTAL for the crystal type oscillator.
Figure 1-4(a)
a typical oscillator circuit for an AT-cut, parallel resonant
2 M
is provided between
Figure 1-4: Oscillator Connections
MCU
36 pF
(a) Crystal or
Ceramic Resonator
Connections
EXTAL
XTAL
36 pF
unconnected
External Clock
(b) External
Clock Source
Connection
EXTAL
XTAL
MCU
相關PDF資料 |
PDF描述 |
|---|---|
| 68HC705BD7 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 68HC05C0FN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C0P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。