- 您現在的位置：買賣IC網 > PDF目錄369230 > 68HC05BD7 (Motorola, Inc.) 8-Bit Microcontroller Units (MCU).(8位微控制器) PDF資料下載
參數資料
| 型號： | 68HC05BD7 |
| 廠商： | Motorola, Inc. |
| 英文描述： | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 中文描述： | 8位微控制器單元（MCU）。（8位微控制器） |
| 文件頁數： | 18/85頁 |
| 文件大?。?/td> | 302K |
| 代理商： | 68HC05BD7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
MOTOROLA
Page 8
SECTION 1: GENERAL DESCRIPTION
GENERAL RELEASE SPECIFICATION
MC68HC05BD7 Rev. 2.0
line (SCL) of DDC12AB. These two pins are open-drain pins. See
SECTION 7
for how to
configure the pins. See
SECTION 9
for a detailed description.
1.2.4
RESET
This active low input-only pin is used to reset the MCU to a known start-up state. The
RESET pin contains an internal Schmitt trigger as part of its input to improve noise
immunity. See
SECTION 5
for more details.
1.2.5
PA0-PA7
These eight I/O lines comprise Port A. The state of any pin is software programmable and
all Port A lines are configured as inputs during Reset. See
SECTION 7
for a detailed
description of I/O programming.
1.2.6
PB0-PB5
These six I/O lines comprise Port B. The state of any pin is software programmable and all
Port B lines are configured as inputs during Reset. PB2 to PB5 are +12V open-drain pins.
See
SECTION 7
for a detailed description of I/O programming.
1.2.7
PC0*/PWM8*-PC1*/PWM9*
These two +12V open-drain pins are either 8-bit PWM channels 8 to 9 outputs or general
purpose I/O port C. The state of any pin is software programmable and all Port C lines are
configured as inputs during Reset. See
SECTION 7
for a detailed description of I/O
programming.
1.2.8
PC2/PWM10/ADC0- PC5/PWM13/ADC3
These four pins can be selected as general purpose I/O of port C, PWM or ADC input
channel 0-2. See
SECTION 7
for how to configure the pins. Also see
SECTION 8
and
SECTION 12
for a detailed description of these modules.
1.2.9
PC6/PWM14/VSYNO, PC7/PWM15/HSYNO
These two pins can be selected as general purpose I/O of port C, PWM or sync signal
outputs. See
SECTION 7
for how to configure the pins. Also see
SECTION 8
and
SECTION
10
for a detailed description of these modules.
1.2.10
PD0*/SDA*, PD1*/SCL*
These pins are either general purpose I/O pins of port D or the data line (SDA) and clock
1.2.11
PD2***/CLAMP, PD3*/SOG
The PD2*** is +5V open-drain general purpose I/O pin and the PD3* is +12V open-drain
general purpose I/O pin. The PD2 pin could become the CLAMP pulse push-pull output to
Pre-AMP IC and the PD3 pin could become the SOG digital input of the Sync Processor
when the corresponding enable bit in SPIOCR register is set. These two pins will not be
bonded out in 40-pin DIP package.
相關PDF資料 |
PDF描述 |
|---|---|
| 68HC705BD7 | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC05J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
| 68HRC705J5A | 8-Bit Microcontroller Units (MCU).(8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 68HC05C0FN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C0P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AFN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| 68HC05C4AP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。